One of the only bits of maintenance an internally geared hub needs is occasional oiling. Using the proper oil is essential, and, if you have a Shimano Alfine hub, you've found the right stuff. - Mineral oil based lubricant specifically for the Alfine 11-speed hub

Shop-quality, adjustable torque driver that limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The ATD-1.2 features all-metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at Park Tool's factory in Minnesota.

Going for a ride but don't know what to pack? No problem, Blackburn has you covered. The new Local CO2 Ride Kit offers up what you need to get home, and extra carrying capacity to bring along anything else. - Local Small seat bag offers extra space to pack your tube, wallet, phone, or whatever you want - Wayside CO2 inflator with 16g cartridge - GRID 8 Mutli-tool provides a quality tool to make sure your bike is adjusted properly for your ride - 2x tire levers

Accurately gauge the straightness of disc brake rotors while the wheel is mounted in a TS-2.2 or TS-2 Professional Wheel Truing Stand (each sold separately). Park Tool's Rotor Truing Gauge features an infinitely adjustable, finely threaded indicator gauge. It works with any diameter brake rotor.

Dial Indicator Set bolts directly to the DT-3 allowing for greater accuracy and a way to measure results. Now includes an elongated, cylindrical tip that is large enough to work around voids in most rotors.

A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings. The Chain Gang includes: - CM-5.3 Cyclone Chain Scrubber - GSC-1 GearClean Brush - 8 oz. bottle of Bio ChainBrite The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.

Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)

The ultimate trailside companion. These high tensile steel multi-tools feature a precise fit and finish and side grips for a secure handhold even with gloves on. The m19 includes: - Chain tool: 8/9/10 speed compatible - Spoke wrench: #0, 1, 2, 3 - Hex wrenches: #2, 2.5, 3, 4, 5, 6, 8 - Open wrench: 8mm, 10mm - Screwdrivers: Phillips #1, Phillips #2, flat #2 - Torx: t-10, t-25 - Stainless steel carrying case - Length: 89 mm - Weight: 175g - Warranty: lifetime

- Protects rotor and calipers from overspray and while in transit - Quick and easy to use, fits all MTB and road rotors - Simply rinse and use again - Breathable neoprene

- Heavy-duty device that cleans chain in seconds - The kit includes a 75 ml bottle of Drivetrain Cleaner that can be either sprayed over the drivetrain or poured into the top reservoir - Liquid release button ensures the application of the cleaner is quick and easily controlled. - Abrasive cleaning teeth and rotating brush wheels which have 120 contact points cover every part of each chain link for a deep and thorough clean - Excess dirty fluid drops into a second lower reservoir so it’s kept away from the clean chain

- Pocket sized chain tool that mates perfectly with Topeak ratchets and torque tools - Compatible with single and multispeed chains up to 12 speed including Capagnolo chains - Includes a 4/5mm allen key and a chain hook as well as a rubber clip to hold

- Used to install fork dust seals

- Heavy duty double-ended steel lockring wrench - 10.5" long for plenty of leverage, fits most bottom bracket lockrings

Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-3 has 1.3mm tips on bent nose blades for medium, external snap rings.

Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-2 has 1.3mm tips on bent nose blades for medium, internal snap rings. The tips of the RP-2 open from 22mm down to 2mm (center to center).

Also called a sleeping hub, the Dummy Hub slides into rear dropouts and replaces the rear wheel for chain cleaning and transport. The DH-1 works with all derailleur and 1/8" chain. The unique design allows the bike to be shifted and works with open dropout and thru-axle frames up to 12mm.

Park's Hydraulic Brake Piston Press is used to set or reset the piston(s) inside hydraulic disc brake calipers during installation, maintenance and repair. Just push it into the caliper to wedge the piston into place. It's made of tough tool steel with a comfortable and oversize rubber handle for a great grip.

- Developed by the Boeing company for lubrication and protection of aircraft components - Dries to a thin waxy film that clings to metal for months - Law prohibits ORM-D materials from shipping by air

Rock-N-Roll Gold lubricant is for both mountain and road bike use. The formulation goes deep down into the chain and traps any dirt. Then, with the energy of the chain freewheeling backwards, the dirt and grit floats to the surface so you can wipe it all off, leaving a new and clean application of lube inside the chain, where it's needed. - All-purpose lube - Cleans and lubricates simultaneously

The ultimate trailside companion. These high tensile steel multi-tools feature a precise fit and finish and side grips for a secure handhold even with gloves on. The m10 includes: Hex wrenches: #2, 2.5, 3, 4, 5, 6, 8 Screwdrivers: Phillips #2, flat #2 Torx: t-25 Length: 89 mm Weight: 124g Warranty: Lifetime

The use of cutting oil or fluid is extremely important when performing any cutting, tapping, facing or reaming operation and Park's Cutting Fluid is a high quality, environmentally safe cutting fluid that extends tool life and makes any frame prep job easier and safer. CF-2 can effectively be used on all metals.

Park's AV-1 Axle Vise makes repairing and overhauling hubs easier than ever. It prevents your axle from spinning while work is done on the hub and it has two different size receptacles so it will work with both front and rear axles.

8 functions—we've gone out of our way to pack this tool with as many useful functions as humanly possible. The selection, length, and placement of each tool has been carefully thought out so that you have the right tool and can easily use it. - 110 grams

Bike Protect is the ultimate liquid bicycle protection. Preserve and freshen your bike with Bike Protect's incredible water dispersing action! It's a perfect 'all over', after-wash corrosion inhibitor due to its extremely high oil content. This increased oil content creates the finest bike protection spray on the market. It drives out moisture and leaves a sparkling, non-sticky protective layer on your frame, drive chain, metal parts, and paintwork. It's ideal to spray onto your chain to drive out moisture before you apply any of the brilliant Muc-Off chain lubes. Bike Protect doesn't just disperse water after you've given your bike a good clean. It also prevents dirt adhesion between washes and reduces future maintenance time as well as helping reduce friction, wear, and energy consumption. - High performance formula leaves dry, non-sticky, protective film - Safe on frame, metal parts, plastics, rubber, paint, and carbon fiber - Drives out excess moisture - Prevents dirt adhesion - Light lubricant coats moving parts - Quick and easy to use - Aerosol Spray - Ideal for Road Cycling, Cyclocross, MTB, & Fat Bikes - Provides the ultimate performance in freezing conditions - For chains, cables, shifters, derailleurs, pedals, & cleats - Incredible durability - Pipette system for easy application

Park Tool's CTP-4K includes four replacement chain tool pins and one 5/32" ball bearing. To replace the chain tool pin, unscrew the cap, and pull out the old pin. Use care not to lose the ball bearing beneath the pin. Install the new pin and replace the cap. Works with the CT-4.3, CT-4.2, CT-4, and CT-11

Specially designed for crank bolts, freehub removals and pedal installs and removals, Park's Hex Tools are built for speed, leverage and comfort. Their super-precise hex heads and dual-density, ergonomic handle mean the HTs may soon become your new favorite tools.

Because even your reliable Mavic wheels will eventually need truing, Park offers their Spoke Wrench For Mavic Wheel Systems. This comfortable, vinyl-coated, double-ended spoke wrench easily accesses and turns Mavic nipples. One end fits Mavic 6-spline, 9mm threaded eyelets and the other fits their 7-spline, 6.4mm nipples.

Fingerprints and glossy marks are now a thing of the past. Matte Finish Detailer has been specifically developed for satin matte paints, matte finishes and matte vinyl wraps. The premium-grade formula will leave any matte surface with a streak and gloss-free protective finish that reduces dirt adhesion. - Quick to use spray developed specifically for matte finishes - Leaves a non-sticky, streak and gloss-free protective finish - Carbon Fiber safe - Biodegradable

White Lightning's Epic Ride lets you take on that all day ride and hear only the birds chirping, not your chain squealing. Its unique formula features premium non-petroleum synthetics that provide unheard of durability without the grimey build-up common with synthetic oils. This versatile lube also works wonders on derailleur cables and suspension seals. And, good news for the forgetful amongst us, Epic Ride is lube-and-go, no prep or dry time required!

Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.